Store   

Menu
24 Month Warranty

Returns & Warranties

We are proud of the products we sell and we hope you have a great experience. If you believe a product you purchased from the Canon Store is defective, then you may have a right of return and/or other remedies under either our voluntary warranty (please refer below or to your Warranty Card) and/or the Consumer Guarantees under the Australian Consumer Law - see consumerlaw.gov.au

CANON MANUFACTURER’S WARRANTY FOR CONSUMER IMAGING PRODUCTS
(applies to purchases made on or after 20 July 2015)

This warranty applies to Canon consumer products (Products) that are purchased in Australia or New Zealand from Canon Australia Pty Ltd or Canon New Zealand Limited (Canon) or their respective authorised distributors, dealers or retailers.

Canon-branded products purchased from other sources (including ‘grey’, ‘parallel’ or ‘direct’ imports) are not covered by this warranty. These products may come with a different warranty offered by the retailer or relevant sales company based in another country.

You will need proof of purchase to make a warranty claim so please keep your receipt and warranty card safe. You can also register your product on our website as a record of your purchase.

Consumer Guarantees

You have rights under applicable Australia and New Zealand consumer laws.

For goods supplied in Australia only: Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.

For goods supplied in New Zealand only: This warranty applies in addition to your rights under the Consumer Guarantees Act 1993. Further information on the Consumer Guarantees Act is available from Consumer Affairs.

Canon manufacturer’s warranty

In addition to your consumer rights, Canon offers the following manufacturer’s warranty:

  1. With normal use and service, during the Warranty Period stated below, Canon warrants the Products will be free from defects arising wholly or substantially from faulty parts, manufacture and workmanship:

    Product: purchased new and unused, or Canon-refurbished product (not second hand) Warranty Period (from date of purchase)
    Projector Products (excluding lamps) and standard accessories 36 months
    Projector Lamps 6 months
    Image Stabilizer binoculars 24 months
    IP/Network Video Cameras 24 months
    Interchangeable and fixed lens cameras 24 months
    Cinema EOS products 24 months
    Canon camera lens 24 months
    Digital Video Cameras 24 months
    PIXMA PRO Range 24 months
    All other consumer products and their standard Canon accessories 12 months
  2. Canon’s warranty does not cover:

    1. replacing consumables including print heads, drums, lamps, film, ink, toner and paper;
    2. rubber rollers in scanners; or
    3. any software included with the Products.
  3. Canon’s warranty does not apply where damage is caused by external factors including:

    1. normal wear and tear;
    2. damage caused outside Canon’s control such as accidents, vandalism or burglary;
    3. your negligent or improper use of the Products including failing to follow operating instructions;
    4. leaking batteries;
    5. liquid exposure (except water for waterproof Products) or infiltration of foreign particles;
    6. repairs or modification of the Products except by Canon, or its authorised service agents;
    7. using unsuitable ink or toner or other materials in the Products;
    8. using any accessories, supplies, parts or devices (including batteries, tapes/cards, lenses and flash attachments) not conforming to Canon’s specifications; or
    9. shipping or other transit.
  4. Subject to your rights under consumer law, Canon excludes all liability in respect of the Product for any loss that is not reasonably foreseeable from a failure of the Product, which may include liability for negligence, loss of tape/card, loss of images, loss of data, loss of expenditure associated with the Product, losses incurred while the product is being repaired and loss of enjoyment.
  5. This warranty is not transferrable.


MAKING A WARRANTY CLAIM

The process for making a claim may differ for some products. Please see the claims processes below.

Projectors (only those purchased in Australia)

To make a claim notify Canon as soon as possible by telephoning 1300 799 604 (Australia).

You may be asked to provide a written description of the problem, images or other relevant material. Remember, please have your proof of purchase ready. The service team will try to troubleshoot the problem with you first.

If your projector problem cannot be rectified over the phone, Canon will organise for it to be collected and a replacement model will be delivered to you upon receipt. Ownership of the faulty projector will pass to Canon upon receipt by Canon or its agents. Replacement projectors will be the same and/or equivalent projector model, subject to availability. The replacement model may be a new or refurbished ‘as new’ unit projector, determined at the discretion of Canon.

(please note – Canon will pay for courier costs to pick up any faulty units as identified by our customer care trouble shooting team, however costs for unmounting projectors and/or securely and safely packaging them for safe travel back to Canon is at the cost of the end user)

Document Scanners*, Faxes** and Micrographics (only those purchased in Australia)

* Does not apply to P Series Scanners
** Applies only to those models of laser faxes that can also be used as stand alone printers

To make a claim, notify Canon as soon as possible by telephoning Canon on 13 13 83 (Australia). You may be asked to provide a written description of the problem, images or other relevant material. The service team may try to troubleshoot the problem with you first. Remember, please have your proof of purchase ready.

If the warranty claim is accepted Canon will, at its cost, repair or replace any faulty parts or rectify any faulty workmanship.

Where the Product is located:

  1. within a 25km radius of a Canon Direct Service Centre:

    warranty repairs will be carried out on-site by Canon or Canon authorised service agents; and Canon will use its best endeavours to carry out such repairs by the end of the day after Canon receives notice of the warranty claim (except that this period shall not include weekends or public holidays).

  2. outside a 25km radius: a fee will be charged for provision of on site warranty services. 

All other products
To make a claim, notify Canon or our authorised service agents as soon as possible by telephoning Canon on 13 13 83 (Australia) or 0800 222 666 (New Zealand). You can also email Canon Australia by submitting an enquiry at: www.canon.com.au/en-AU/Personal/Support-Help You can email Canon New Zealand at: helpdesk@canon.co.nz Or see: canon.com.au/warranty (Australia) or canon.co.nz/warranty (New Zealand)

You may be asked to provide a written description of the problem, images or other relevant material. The service team may try to troubleshoot the problem with you first. Remember, please have your proof of purchase ready. If we need to examine the Product then, except as otherwise required by consumer law, you must pay for all packing, freight and insurance costs to ship the Product to Canon or its authorised service agent. 

If Canon accepts your warranty claim, we will, at our cost (and subject to your rights under consumer law) repair or replace any faulty parts or rectify any faulty workmanship, and return the Product to you.
If your warranty claim is not accepted, Canon or its authorised service agents may still be able to resolve your problem, where that service is charged at our standard rates (only with your prior approval).

Features

The EOS 8OD, supported with Camera Assist is a powerful, fully equipped DSLR providing you with everything you need at your fingertips to advance your photography and video skills. Ideal for experimenting with different photography genres and styles, the EOS 80D is highly customisable and shoots with exceptional speed. Combining leading imaging technologies - including a new 24.2 megapixel CMOS sensor and DIGIC 6 processor, alongside a new 45 all cross-type point AF System and fast responsive 7 fps shooting rate - the EOS 80D is a versatile camera for capturing striking stills and Full HD movies.

Camera Assist
Get started, get creative and get connected with your Canon camera. Explore the video series designed to help you get to know your new camera and find out how easy it is to share your photos instantly.
To view the tutorials scroll down to Compatibility & Support.

Selected shots from the EOS 80D Single Kit

Accessories

Specifications

Sensor

HideShow
Sensor Type CMOS
Total Pixels Approx 25.80 megapixels
Aspect Ratio 3:2
Filter Low-Pass Filter: Built-in/Fixed with fluorine coating
Sensor Cleaning EOS integrated cleaning system
Colour Filter Type Primary Colour

Processor

HideShow
Processor Type DIGIC 6
Face Detection Technology Available
Compatible Lens Mount EF Lens, EF-S Lens
Focal Length Equivalent to 1.6x the focal length of the lens
Other Zoom Playback zoom: .5x - 10x

Focusing

HideShow
Focusing Type TTL-CT-SIR with a CMOS sensor
AF System/ Points 45 cross-type AF points (45 f/5.6 cross-type AF points, 27 f/8 points [9 cross-type], centre point is f/2.8 and f/5.6 dual cross-type) (11)
AF working range EV -3 - 18 (at 23°C & ISO100)
AF Modes AI Focus, One Shot, AI Servo
AF Point Selection Automatic selection: 45 point AFManual selection: Single point AFManual selection: Zone AF Manual selection: Large Zone AFAF points can be selected separately for vertical and horizontal shooting
Selected AF point display Indicated by a transmissive LCD in viewfinder and Quick Control screen
Predictive AF Yes, up to 8m
AF Lock Locked when shutter button is pressed half way in One Shot AF mode.
AF Assist Beam Intermittent firing of built-in flash or emitted by optional dedicated Speedlite
Manual Focus Selected on lens
AF Microadjustment C.Fn II-16, +/- 20 steps (wide and tele setting for Zooms), Adjust all lenses by same amount, Adjust up to 40 lenses individually, Adjustments remembered for lens by serial number

Exposure Control

HideShow
Metering modes 7560-pixel RGB+IR metering sensor, Metering with the area divided into 63 segments (9×7),(1) Evaluative metering (linked to all AF points) (2) Partial metering (approx. 6.0% of viewfinder) (3) Spot metering (approx. 3.8% of viewfinder) (4) Center-weighted
Metering Range EV 1-20 (at 23°C with 50mm f/1.4 lens ISO100)
AE Lock Auto: In One-shot AF mode with evaluative metering exposure is locked when focus is achieved. Manual: By AE lock button in creative zone modes.
Exposure Compensation Auto: In One-shot AF mode with evaluative metering exposure is locked when focus is achieved. Manual: By AE lock button in creative zone modes.
AEB 2, 3, 5 or 7 Shots +/-3 EV 1/3 or 1/2 stop increments
ISO Sensitivity Auto (100-16000), 100-16000 (in 1/3-stop or whole stop increments) ISO can be expanded to H: 25600During Movie shooting: Auto (100-12800), 100-12800 (in 1/3-stop or whole stop increments) ISO can be expanded to H: 25,600

Shutter

HideShow
Type Electronically-controlled focal-plane shutter
Shutter Speed 30-1/8000 sec (1/2 or 1/3 stop increments), Bulb (Total shutter speed range. Available range varies by shooting mode)

White Balance

HideShow
White Balance Type Auto white balance with the imaging sensor
White Balance Settings AWB (Ambience priority, White priority), Daylight, Shade, Cloudy, Tungsten light, WhiteFluorescent light, Flash, Custom, Colour Temperature Setting.White balance compensation: 1. Blue/Amber +/-92. Magenta/ Green +/-9
Custom White Balance Yes, 1 setting can be registered
WB Bracketing +/-3 levels in single level increments 3 bracketed images per shutter release. Selectable Blue/Amber bias or Magenta/Green bias

Viewfinder

HideShow
Viewfinder Type Pentaprism
Coverage (Vertical/Horizontal) Approx. 100%
Magnification Approx. 0.95x (4)
Eyepoint Approx. 22mm (from eyepiece lens centre)
Dioptre Correction -3 to +1 m-1 (dioptre)
Viewfinder Focusing Screen Fixed (Transmissive LCD screen)
Viewfinder Mirror Quick-return half mirror (Transmission: reflection ratio of 40:60, no mirror cut-off with EF600mm f/4 or shorter)
Viewfinder Information AF information: AF points, focus confirmation, AF area selection modeExposure information: Shutter speed, aperture value, ISO speed (always displayed), AE lock, exposure level/compensation, spot metering circle, exposure warning, AEB.Flash information: Fl
Depth of field preview Yes, with Depth of Field preview button.
Viewfinder Eyepiece shutter On strap

Screen

HideShow
Screen Type Touch screen vari angle 7.7cm (3.0") 3:2 Clear View II TFT, approx. 1040K dots
Screen Coverage Approx. 100%
Viewing Angle (horizontally/vertically) Approx. 170°
Coating Anti-reflection, Solid Structure and Anti smudge
Screen Display Options (1) Quick Control Screen (2) Camera settings (3) Dual Axis Electronic Level
Screen Brightness Adjustable to one of seven levels
Built-in Flash GN (ISO 100, meters) 12
Built-in Flash Coverage up to 17mm focal length (35mm equivalent: 28mm)
Built-in Flash recycle time Approx. 3 seconds
Flash Modes Auto, Manual flash, Integrated Speedlite Transmitter
X-sync 1/250sec
Red-Eye Reduction Yes - with red eye reduction lamp
Flash Exposure Compensation +/- 3EV in 1/2 or 1/3 increments
Flash Exposure Bracketing Yes, with compatible External Flash
Flash Exposure Lock Yes
Second Curtain Synchronisation Yes
HotShoe/ PC terminal Yes/No
External Flash Control via camera menu screen

Shooting

HideShow
Shooting Modes Scene Intelligent Auto (Stills and Movie), No Flash, Creative Auto, SCN(Portrait, Landscape, Close-up, Sports, Night Portrait, Handheld Night Scene, HDR Backlight Control, Food, Kids, Candlelight), Creative filters, Program AE, Shutter priority AE, Apertu
Picture Styles Auto, Standard, Portrait, Landscape, Fine Detail, Neutral, Faithful, Monochrome, User Defined (x3)
Image Processing Highlight Tone Priority, Auto Lighting Optimizer (4 settings) Long exposure noise reduction, High ISO speed noise reduction (4 settings) Multi Shot Noise Reduction, Auto Correction of Lens Peripheral illumination and Chromatic aberration correction, Creat
Drive modes Single, Continuous L, Continuous H, Self timer (2s+remote, 10s +remote), Silent single shooting, Silent continuous shooting
Continuous Shooting Max. Approx. 7fps. (speed maintained for up to 110 images (JPEG)(1)(10)(with UHS-I card), 25 images (RAW)(with UHS-I card)) (2) (10)

Live View Mode

HideShow
Live View Mode Type Electronic viewfinder with image sensor
Live View Coverage Approx. 100% (horizontally and vertically)
Live View Frame Rate 30 fps
Focusing Manual Focus (Magnify the image 5x or 10x at any point on screen)Autofocus: Dual Pixel CMOS AF (Face detection and Tracking AF, FlexiZone-Multi, FlexiZone-Single), Tracking sensitivity (-3 to +3) and Movie Servo AF Speed (-7 to +2)
Metering Real-time evaluative metering with image sensor
Display Options Grid overlay (x3), Histogram, Electronic level

File Type

HideShow
Still Image File Type JPEG: Fine, Normal (Exif 2.30 compliant) / Design rule for Camera File system (2.0), RAW: RAW (14bit, Canon original RAW 2nd edition), Digital Print Order Format [DPOF] Version 1.1 compliant
RAW+JPEG simultaneous recording Yes, any combination of RAW + JPEG, M-RAW + JPEG, S-RAW + JPEG possible.
Image File Size JPEG 3:2: (L) 6000 x 4000, (M) 3984 x 2656, (S1) 2976 x 1984, (S2) 1920x1280, (S3) 720x480, JPEG 4:3: (L) 5328x4000, (M) 3552x2664, (S1) 2656x1992, (S2) 1696x1280, (S3) 640x480
Movie File Type MOV / MP4 (Video: H.264 Intra frame / inter frame, Sound: Linear PCM / AAC, recording level can be manually adjusted by user)
Movie File Size 1920 x 1080 (59.94, 50 fps) inter-frame, 1920 x 1080 (29.97, 25, 23.98 fps) intra or inter frame, 1920 x 1080 (29.97, 25) lite inter-frame, 1280 x 720 (59.94, 50 fps) inter-frame, 1280 x 720 (29.97, 25) lite inter-frame
Movie Length Max duration 29min 59sec, Max file size 4GB (If file size exceeds 4GB a new file will be created automatically)
Folders New folders can be manually created and selected
File Numbering (1) Consecutive numbering (2) Auto reset (3) Manual reset

Other Features

HideShow
Metadata Tag User copyright information (can be set in camera) Image rating (0-5 stars)
LCD Panel / Illumination Yes/Yes
Water/ Dust resistance Yes
Intelligent Orientation Sensor Yes
Playback zoom 1.5x - 10x
Display Formats (1) Single image with information (2 levels), (2) Single image, (3) 4 image index, (4) 9 image index, (5) 36 image index, (6) 100 image index, (7) Jump Display, (8) Movie edit
Slide Show Image selection: All images, by Date, Folder, Movies, Stills, Rating Playback time: 1/2/3/5/10/20 seconds, Repeat: On/Off Background music: On/Off Transition effect: Off, Slide in 1, Slide in 2, Fade 1, Fade 2, Fade 3
Histogram Brightness: Yes, RGB: Yes
Highlight Alert Yes
Image Erase/Protection Erase: Single image, All images in folder, Checkmarked images, unprotected images
Menu Languages 25 Languages: English, German, French, Dutch, Danish, Portuguese, Finnish, Italian, Norwegian, Swedish, Spanish, Greek, Russian, Polish, Czech, Hungarian, Romanian, Ukrainian, Turkish, Arabic, Thai, Simplified Chinese, Traditional Chinese, Korean and Japa
Firmware Update Update possible by the user.

Interface

HideShow
Computer/Other Hi-Speed USB / Video output (PAL/ NTSC) (integrated with USB terminal), HDMI mini output (HDMI-CEC compatible), External microphone (3.5mm Stereo mini jack), Headphone socket (Stereo mini jack)

Direct Print

HideShow
Canon Printers Canon Compact Photo Printers and PIXMA Printers supporting PictBridge
PictBridge Yes

Storage

HideShow
Storage Type SD, SDHC or SDXC (UHS-I)card

Software

HideShow
PC Supported Operating system Windows 10 / 8.1 / 8 / 7(*)* With Microsoft .NET Framework 4.5 is installed. Mac OS X 10.9, 10.10, 10.11
Image Processing Digital Photo Professional 4.4.0 (RAW Image Processing)
Other Software EOS Utility, EOS Lens Registration Tool, EOS Web Service Registration Tool, EOS Sample Music, Picture Style Editor

Power Source

HideShow
Batteries Rechargeable Li-ion Battery LP-E6N (supplied), built in for date & settings
Battery life Approx. 960 (at 23°C, AE 50%, FE 50%) (5)Approx. 860 (at 0°C, AE 50%, FE 50%)
Battery Indicator 6 levels + percentage
Power saving Power turns off after 1, 2, 4, 8, 15 or 30mins.
Power Supply & Battery Chargers AC Adapter AC-E6(N), DC coupler: DR-E6, Battery charger LC-E6, Car Battery charger CBC-E6

Physical Specifications

HideShow
Body Materials Polycarbonate resin with glass fiber
Operating Environment 0 – 40 °C, 85% or less humidity
Dimensions (WxHxD) 139.0 x 105.2 x 78.5mm
Camera Weight Approx. 730g (CIPA testing standard, including battery and memory card)
Barcode 4549292061048

What's included

  • EOS 80D Camera Body
  • EF-S 18-55mm f/3.5-5.6 IS STM lens
  • Battery Pack LP-E6N
  • Battery Charger LC-E6
  • Wide Strap
EOS 80D Single Lenks Kit What's Included

Compatibility & Support

Compatibility


Get to know your Canon EOS 80D.

Canon EOS 80D Tutorial – Introduction & User Guide

Canon EOS 80D Tutorial Guide - Tips and Techniques

Connect your Canon EOS 80D to your iPhone via Wi-Fi

Connect your Canon EOS 80D to your Android phone via Wi-Fi

Downloads

Support FAQs

x
Someone in South Australia just bought
About 1 hour ago